Specifications
| Outside diameter | 3.5 mm |
|---|---|
| Hole diameter | 1.35 mm |
| Jack pin | 1.3 mm |
| Centre pin in the hole | no |
| Barrel length | 9 or 11.6 mm |
| Standard | de facto size, close to IEC 60130-10 type E (3.4 × 1.3 mm) |
| Rating (catalogue part) | PP3-002D: 5 A, 24 V DC; PJ-013D jack: 3.5 A, 24 V DC |
| Polarity | not set by the size: read the symbol |
| Plug | PP3-002D |
| Jack | PJ-013D |
Lookalikes and how to tell them apart
The 4.0 × 1.7 is thicker with a wider hole, the 3.0 × 1.1 thinner, and the 3.5 × 1.1 has the same outside with a smaller hole. Its jack has a 1.3 mm pin.
| Size | Centre pin | Standard |
|---|---|---|
| 3.5 × 1.35 mm | no | de facto size |
| 4.0 × 1.7 mm | no | EIAJ class 2, 3.15–6.3 V |
| 3.0 × 1.1 mm | no | de facto size |
| 3.5 × 1.1 mm | no | de facto size |
| 3.8 × 1.35 mm | no | de facto size |
Before you plug it in
Measure with a caliper: the metal sleeve gives the outside diameter. For the hole, use drill bits as gauges: the largest one that slides in gives the size. If there is a pin in the middle, a bit won’t go in: use the caliper’s inside jaws.
The size says nothing about polarity: look for the symbol (a dot inside a C, with + and −) on the device and on the adapter. Centre positive is the most common.
Open the connector identifier →Not sure it is this size? Enter the outside and hole diameters: the identifier compares 22 DC plug sizes.
Other DC plug sizes
2.0 × 0.6 mm 2.35 × 0.7 mm 2.5 × 0.7 mm 3.0 × 1.1 mm 3.5 × 1.1 mm 4.0 × 1.35 mm 4.0 × 1.7 mm 4.5 × 3.0 mm 4.75 × 1.7 mm 4.8 × 1.7 mm 5.5 × 1.7 mm 5.5 × 2.1 mm 5.5 × 2.5 mm 5.5 × 3.0 mm 5.5 × 3.3 mm 6.3 × 3.0 mm 6.5 × 4.4 mm 7.4 × 5.0 mm 7.9 × 5.5 mm
All DC plug sizes, with a chart →
Frequently asked questions
What jack does a 3.5 × 1.35 mm plug need?
A jack for 3.5 × 1.35 mm plugs, with a 1.3 mm pin, such as the PJ-013D: makers sell plug and jack as a matching pair.
Does a 3.5 × 1.35 mm plug fit a 3.5 × 1.1 mm jack?
It goes in, but loosely: the pin of a 3.5 × 1.1 mm jack is thinner than its 1.35 mm hole, so the contact comes and goes when the cable moves.
Is 3.5 × 1.35 mm a standard size?
Almost: IEC 60130-10 type E is 3.4 × 1.3 mm, within a tenth of a millimetre of this de facto size. Check the voltage and polarity on the label.
Sizes and ratings from the makers’ catalogues (Same Sky, Lumberg, Switchcraft) and the EIAJ and IEC summaries. A plug’s rating is a maximum: the adapter’s label says what it actually supplies.