How to set the address
There is no address pin: the address is set at the factory, so it is always 0x51.
Devices that use the same addresses
Two devices on the same bus can’t answer on the same address. These modules from our list also use 0x51:
| Device | What it is | Shared address |
|---|---|---|
| 24LC256 / 24AA256 / 24FC256 | 256-Kbit I2C EEPROM | 0x51 |
| AT24C32 | 32-Kbit I2C EEPROM | 0x51 |
| PCA9685 | 16-channel 12-bit PWM / servo driver | 0x51 |
| PCF85063A | real-time clock | 0x51 |
If two of them end up on the same address, move one with its address pin, put one behind a TCA9548A multiplexer (0x70–0x77), or use a second I²C bus: the ESP32, ESP32-S3 and RP2040 have two I²C controllers (the ESP32-C3 has one).
Check your whole bus →Add the PCF8563 and your other modules: the checker finds conflicts, suggests free addresses and sizes the pull-ups.
7-bit and 8-bit address
I²C addresses are 7 bits long. Some datasheets and libraries write them as 8-bit numbers, with the read/write bit added on the right: that is why the same chip can appear as 0x51 or 0xA2. Arduino’s Wire library and ESPHome use the 7-bit form.
| 7-bit | Binary | 8-bit write | 8-bit read |
|---|---|---|---|
| 0x51 | 1010001 | 0xA2 | 0xA3 |
Check that it answers
Upload this sketch with the PCF8563 wired to SDA and SCL: it tries every address the chip can use and prints the one that answers. On an ESP32 the default pins are GPIO21 (SDA) and GPIO22 (SCL); on an Arduino Uno, A4 and A5.
#include <Wire.h>
const byte ADDRS[] = {0x51};
void setup() {
Serial.begin(115200);
Wire.begin();
for (byte a : ADDRS) {
Wire.beginTransmission(a);
if (Wire.endTransmission() == 0) {
Serial.print("PCF8563 answers at 0x");
if (a < 0x10) Serial.print('0');
Serial.println(a, HEX);
return;
}
}
Serial.println("No answer: check the wiring");
}
void loop() {}
In ESPHome the bus is scanned at boot (scan: true is the default): the log lists every address that answers.
i2c:
sda: GPIO21
scl: GPIO22
scan: true
Pull-up resistors
SDA and SCL need pull-up resistors to the supply. Many breakout boards already carry them, often 4.7 kΩ or 10 kΩ, and with several boards on the bus they add up in parallel. The I²C checker works out the allowed range for your bus voltage and speed.
Frequently asked questions
What is the I2C address of the PCF8563?
0x51. It is fixed: there is no address pin.
Can I use more than one PCF8563 on the same bus?
Not directly: the address is fixed, so two would clash. Put each one on a different channel of a TCA9548A multiplexer, or use a second I²C bus.
Why doesn’t the PCF8563 show up in an I2C scan?
Check, in this order: SDA and SCL not swapped; ground shared between the boards; pull-up resistors on SDA and SCL; the module powered at the voltage it is made for; and that your code uses the 7-bit address (0x51), not the 8-bit one (0xA2).
Similar devices
24LC256 / 24AA256 / 24FC256 AT24C32 DS1307 DS3231 PCF85063A PCF8523
Addresses checked against the PCF8563 datasheet.